MIMAKI JF-1631 Specifications Page 120
- Page / 142
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
5-6
Error message Cause Corrective measure
The X motor has been overload.
• Turn off the power to the device an
turn it on after a while.
• If the same error message appears
again on the LCD, contact your local
distributor to call for service.
The Y motor has been overload.
Overcurrent error on the X motor
has been detected.
Overcurrent error on the Y motor
has been detected.
Y origin could not be detected.
Head temperature is abnormal
condition.
X origin could not be detected.
Z origin could not be detected.
Top end in the Z-axis can not be
detected
The amount of ink remaining in
the ink cartridge is insufficient.
• Replace an ink cartridge of the
displayed head ahead of time.
(P.4-4)
The ink cartridge has run out of
ink.
• Replace the ink cartridge of which
color is shown on the LCD with a new
one.
( P.4-4)
The ink cartridge is not attached
to the ink station.
• Attach the ink cartridge(s) correspond-
ing with the color shown on the dis-
play.
( P.4-20)
Waste ink tank is full.
• Remove the waste ink tank and set an
empty waste ink tank. ( P.4-22)
Wiping times exceeds the
predetermined value.
• Contact your local distributor to call for
service.
The IC chip of the ink cartridge
cannot be read normally.
• Remove an ink cartridge of the
displayed head and insert it again. If
the error is still displayed after this
operation, call the dealer or our
branch for the service.
ERROR401
MOTO R X
ERROR402
MOTO R Y
ERROR403
X CURRENT
ERROR404
Y CURRENT
ERROR50A
YORIGIN
ERROR50E
HEAD TEMP : 12345678
ERROR510
XORIGIN
ERROR511
ZORIGIN
ERROR511
ZSNSWORK
ERROR601
INK NEAREND:MCYKKCMY
ERROR602
INK END :MCYKKCMY
ERROR603
NO CARTR I DGE
ERROR604
! WS I NKTANK FUL L
ERROR605
!REPLACE WIPER
ERROR606
WRONG CA R T R I DG E
- MIMAKI ENGINEERING CO., LTD 1
- TABLE OF CONTENS 2
- Requests 6
- FCC Statement (USA) 6
- LASER SAFETY 7
- CDRH REGULATION 7
- Foreword 8
- Features 9
- For safe operation 10
- Never do the following 12
- Precautions for use 14
- Notes on UV lamp 16
- Notices for installation 17
- CHAPTER 1 19
- Before Use 19
- Installing the device 20
- Configuration and Function 21
- Operation Panel (JF-1631) 22
- Operation Panel (JF-1610) 23
- Carriage 24
- Capping Station 24
- Flushing BOX 24
- EMERGENCY SWITCH 25
- Connecting the cables 26
- UV irradiation device 27
- Function of indicator 27
- Setting of ink cartridge 28
- Handling of white ink 29
- About Media 30
- Menu mode 31
- CHAPTER 2 33
- Basic Operations 33
- When setting the media 34
- When drawing the image 34
- Operation flow 35
- Turning the power ON 36
- Setting the media 37
- Setting the media on JF-1631 38
- On the absorption area 39
- Using of Roll Sheet 40
- Test drawing 41
- Execution of head cleaning 42
- When cleaning with “Wiping” 43
- Priority is set to “HOST” : 44
- “HOST” is displayed 44
- Priority is set to “PLOT” : 44
- Interruption of drawing 45
- Move the Y-bar 45
- FUNCTION 46
- Turning the power OFF 47
- CHAPTER 3 49
- Useful Function 49
- Changing origin 50
- • Set value : 0.0 to 50.0mm 52
- Adjusting head gap 54
- Registering Head gap value 55
- Turing the UV lamp off 56
- Other useful functions 57
- Each setting 58
- Setting of priority 61
- • Default is “English.” 62
- Output the setting list 63
- Other useful settings 65
- Initializing set contents 66
- For setting media correctly 67
- CHAPTER 4 69
- Routine maintenance 70
- Ink cartridge 72
- Ink cartridge trouble 73
- Cleaning flushing BOX 74
- Articles required 76
- Set the empty waste ink tank 78
- Remove the filter Assy 80
- INT.WIPING 82
- PR I NT COUNT = 10 82
- MA I NT ENANCE 82
- INT.WIPING <ent> 82
- Samples of pattern drawn 83
- Press the key 84
- Changing the ink set 85
- Filling the ink 88
- Head maintenance function 92
- Special refresh 93
- Cleaning of wiper and cap 94
- COOL I NG 98
- WA S T E A F : e n t 98
- WATER CHNG 100
- SET AF : e n t 100
- Replacing exhaust blower 101
- Daily Maintenance 103
- Cleaning of UV lamp filter 104
- Replacing UV lamp 106
- Checking UV ink curing level 109
- Adjusting UV light level 110
- LEVEL CHECK 112
- WI PE START : en t 112
- HEAD MOVE : e n t 112
- Check the measured value 114
- CHAPTER 5 115
- In Case of Trouble 115
- If image quality declines 117
- Resolving nozzle clogging 117
- Error message 119
- CHAPTER 6 123
- Appendix 123
- Specifications 124
- Specifications for ink 125
- Position of the warning label 126
- Function Flowchart 129
- To be followed To be followed 130
- X OFFSET , Y OFFSET 130
- Followed Followed 132
- Japanese , English 138
- D201645-20-29082008 141
- FW : 2.80 142
- Printed in Japan 142
Related products and manuals for Print & Scan MIMAKI JF-1631
Print & Scan MIMAKI UJV500-160 User Manual
(32 pages)
(32 pages)
Print & Scan MIMAKI UJF-3042HG Specifications
(156 pages)
(156 pages)
Print & Scan MIMAKI UJF-3042HG User Manual
(73 pages)
(73 pages)
Print & Scan MIMAKI JV33-130 Specifications
(152 pages)
(152 pages)
Print & Scan MIMAKI JV5-320S Specifications
(298 pages)
(298 pages)
Print & Scan MIMAKI UJV500-160 Specifications
(156 pages)
(156 pages)
Print & Scan MIMAKI JV3-160S Setup Guide
(170 pages)
(170 pages)
Print & Scan MIMAKI UJF-706 Specifications
(184 pages)
(184 pages)
Print & Scan MIMAKI JV3-130SPII Specifications
(142 pages)
(142 pages)
Print & Scan MIMAKI JV5-130S Specifications
(292 pages)
(292 pages)
Print & Scan MIMAKI JV5-320S Specifications
(130 pages)
(130 pages)
Print & Scan MIMAKI Tx2-1600 Instruction Manual
(166 pages)
(166 pages)
Print & Scan MIMAKI UJF-6042 User Manual
(2 pages)
(2 pages)
Print & Scan MIMAKI TS5-1600AMF User Manual
(22 pages)
(22 pages)
Print & Scan MIMAKI JV33-160 Specifications
(202 pages)
(202 pages)
Print & Scan MIMAKI JV3-75SPII Specifications
(150 pages)
(150 pages)
© 2020, manymanuals.com. All rights reserved. | 2.734 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals