MIMAKI JV3-160S Setup Guide Page 32
- Page / 170
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
– 2.14 –
2-2. Ink system
2-2-1. Definitions
Ink system
Ink system is the general term of a mechanism specific to ink-jet printing system for
protecting a nozzle against troubles such as clogging and recovering it if it should be in
trouble.
Head capping
Head capping is a mechanism for automatically capping the nozzle so as to prevent it
from drying. As long as the head is on the station in the right-hand side cover, it is capped.
Clogged nozzle
In such an event that a specific nozzle fails to discharge any ink because the ink in the
head has thickened or the nozzle itself has dried up, the nozzle called the “clogged nozzle.”
Deflection
A finished state of a drawing on which lines are not plotted straight since a specific nozzle
has failed to discharge ink straight on the paper because of the dust-accumulated or damaged
nozzle surface.
Satellite
Discharged ink is shot as main drops or satellite drops.
If satellite drops are contained in main drops, the ink shot may shift.
Head cleaning
Recovers normal ink discharge by removing bubbles in the head and foreign objects on
the head surface.
Wiping
Wipes the nozzle surface with wiper rubber surface to fix the condition of nozzle holes in
order to remove foreign objects or ink leakage on the nozzle surface.
Flashing
Make idling discharges of ink which may thicken at the point of the nozzle, for refreshment.
Ink suction
Absorbs ink from nozzle by means of the ink suction pump.
Sleep refresh
If the front power switch is turned off when the main power switch is on, the sequence of
power-on R nozzle refresh R power-off is automatically repeated at fixed intervals to
prevent nozzle plugging.
- JV3 Series 1
- FOREWORD 3
- TABLE OF CONTENTS 4
- CHAPTER 3 TROUBLESHOOTING 4
- CHAPTER 4 ADJUSTMENT 5
- CHAPTER 1 9
- OVERVIEW OF MAINTENANCE 9
- 1-1. Cautions in maintenance 10
- 1-4. Names of parts 12
- 1-4-2. Rear face 13
- Name Function 13
- 1-5. Specifications 14
- Item JV3-130S JV3-160S 15
- JV3 series specified ink 16
- 1Solvent ink (SPC-0334∗) 8 16
- – 1.10 – 18
- CHAPTER 2 19
- EXPLANATION OF OPERATION 19
- 2-1-1. Operations 20
- Heater block diagram (2/2) 22
- 2-1-2. Power supply 23
- 2-1-3. Main PCB 23
- Main PCB block diagram 24
- Main PCB Connector signals 25
- 2-1-4. 1394 PCB 27
- 2-1-5. I/F Connection PCB 27
- 2-1-6. IO PCB 28
- IO PCB Connector signals 28
- 2-1-7. IO2 PCB 29
- IO2 PCB Connector signals 29
- 2-1-8. Slider PCB 30
- Slider PCB Connector signals 30
- 2-1-9. Linear encoder PCB 31
- 2-1-10. The KeyBoard PCB 31
- 2-1-11. Take-up motor PCB 31
- 2-1-12. ID contact board 31
- 2-2. Ink system 32
- Refreshing operation 34
- Standby state 34
- Ink end monitoring 34
- Head cleaning operation 35
- Ink cartridge replacement 35
- Miscellaneous 35
- Ink parameters 1 36
- 2-2-4. IC Chip Function 37
- IC chip detecting timing 37
- CHAPTER 3 39
- TROUBLESHOOTING 39
- – 3.10 – 48
- 3-3-3. Cutting failure 49
- 3-3-4. Faulty cutter 50
- 3-3-5. Fan motor 51
- 3-3-7. Abnormal ink shot 52
- – 3.15 – 53
- 3-3-11. Cannot read the IC 54
- Main PCB 54
- 3-4. Plotting failure 55
- 3-4-2. Abnormal print 56
- – 3.19 – 57
- – 3.20 – 58
- – 3.21 – 59
- – 3.22 – 60
- – 3.23 – 61
- – 3.24 – 62
- 3-4-10. Banding occur 63
- 3-4-11. Vertical stripes 63
- 3-4-13. Ink drop or mist 64
- CHAPTER 4 65
- ADJUSTMENT 65
- 4-2. Maintenance item 68
- Pertinent Wiper height 75
- Pertinent Cap height 75
- (Insert from front side) 76
- Screw (M3) 76
- Wiper adjusting plate 0.5 76
- Cap adjusting plate 0.5 76
- Suction side connection joint 78
- Mounting screw 80
- Linear sensor PCB assy 80
- Optical axis 80
- – 4.17 – 81
- 4-2-12. Heater Replacement 83
- • Do not remove the cap bolt 84
- Write a number 85
- 4-2-13. Replacement Fuse 89
- – 4.26 – 90
- CHAPTER 5 91
- MAINTENANCE MODE 91
- 5-1. Maintenance items 92
- #PARAMETER 93
- key and 94
- Head2 Head1 99
- #PRN. adjust2 V2 101
- Y Bi. 1-1 : 0.0 101
- FINAL. 1-2 : 0.0 101
- FUNCTION 102
- Replace count 106
- 5-3-6. CAPPING 108
- 5-3-7. HEAD ID 109
- 5-3-8. SERIAL NO 110
- 5-3-9. DEALER NO 111
- 5-3-10. WORM WHEEL 112
- 5-3-13. SET QUALITY 117
- 5-3-14. MEDIA COMP2 118
- REMOTE/LOCAL 122
- 5-4-4. X SERVO 129
- 5-4-5. Y SERVO 130
- 5-4-6. XY SERVO 131
- 5-4-13. PUMP MOTOR 142
- 5-5. #PARAMATER items 153
- – 5.64 – 154
- – 5.69 – 159
- Error messages 159
- 5-7. Updating the firmware 160
- – 5.73 – 163
- – 5.74 – 164
- CHAPTER 6 165
- MAINTENANCE MENU TREE 165
- 6-1. Maintenance menu tree 166
- D500200-1.00-13122002 170
Related products and manuals for Print & Scan MIMAKI JV3-160S
Print & Scan MIMAKI UJF-706 Specifications
(184 pages)
(184 pages)
Print & Scan MIMAKI JV3-130SPII Specifications
(142 pages)
(142 pages)
Print & Scan MIMAKI JV5-130S Specifications
(292 pages)
(292 pages)
Print & Scan MIMAKI JV5-320S Specifications
(130 pages)
(130 pages)
Print & Scan MIMAKI Tx2-1600 Instruction Manual
(166 pages)
(166 pages)
Print & Scan MIMAKI UJF-6042 User Manual
(2 pages)
(2 pages)
Print & Scan MIMAKI TS5-1600AMF User Manual
(22 pages)
(22 pages)
Print & Scan MIMAKI JV33-160 Specifications
(202 pages)
(202 pages)
Print & Scan MIMAKI JV3-75SPII Specifications
(150 pages)
(150 pages)
© 2020, manymanuals.com. All rights reserved. | 0.605 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals