MIMAKI JV3-160S Setup Guide Page 92
- Page / 170
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
– 5.2 –
5-1. Maintenance items
The maintenance mode has been prepared for the operations to be conducted for adjustment
at the time of delivery of product and for adjustment in maintenance works. This mode is not
released to general users.
Under the maintenance mode, “#Adjustment” items, “#Test” items and “#Parameter” items
are included in functions.
#ADJUST
PRINTadjust2 .................................... Corrects the dot shot timing of each head.
HEAD ADJUST ............................... Adjusts the position displacement mechanically for each head.
WASH ................................................ Head is cleaned.
REPLACE COUNTER ..................... The number of times of replacing ink cartridges is confirmed.
DEFAULT SET ................................ Various parameters are reset to the value at the time of delivery
from the factory.
CAPPING .......................................... Capping position is adjusted.
HEAD ID .......................................... The ID for each head is entered.
SERIAL No ....................................... Enter a serial number.
Deler No ............................................ Enter a dealer number.
WORM WHEEL ................................ Perform eccentric correction of worm gears.
ADJUST EDGE ................................. Right and left dead space sizes are adjusted.
500mm SQUARE .............................. Distance accuracy is adjuted.
SET QUALITY .................................. Sets the operation mode for plot quality.
MEDIA COMP2 ................................ Corrects the amount of media feed.
#TEST
CHECK PATTERN .......................... Nozzle check/density pattern is plotted.
PARAMETER DRAW ..................... Plots the contents of the flash memory.
ALL PATTERN ................................. Collectively plots the adjustment condition check pattern for head or dot
position.
X SERVO ......................................... X-motor aging is carried out.
Y SERVO ......................................... Y-motor aging is carried out.
XY SERVO ....................................... XY-motor aging is carried out.
HEATER TEST ................................. Performance of Print heater and Pre heater is checked.
ACTION TEST ................................. Performance of the wiper, cutter and winding motor is checked.
SENSOR TEST ................................. Performance of various sensors is checked.
PAPER SENSOR .............................. Read-out value of the paper width sensor is checked.
KEYBOARD ..................................... The state of the keyboard is checked.
LCD TEST ........................................ Check the LCD display condition.
PUMP MOTOR ................................ Performance of the pump motor is checked.
TIMER CHECK ............................... Performance of the timer under the power-off state is checked.
MEMORY CHECK .......................... Memory check is carried out.
SKEW CHECK .................................. Check the amount of paper shift.
TEMP CHECK .................................. Check the temperature around the head.
ENCODER CHECK .......................... Check the Linear Scale and Linear Sensor if they perform correctly.
INK IC CHECK ................................ Check the ink cartridge IC if they perform correctly.
- JV3 Series 1
- FOREWORD 3
- TABLE OF CONTENTS 4
- CHAPTER 3 TROUBLESHOOTING 4
- CHAPTER 4 ADJUSTMENT 5
- CHAPTER 1 9
- OVERVIEW OF MAINTENANCE 9
- 1-1. Cautions in maintenance 10
- 1-4. Names of parts 12
- 1-4-2. Rear face 13
- Name Function 13
- 1-5. Specifications 14
- Item JV3-130S JV3-160S 15
- JV3 series specified ink 16
- 1Solvent ink (SPC-0334∗) 8 16
- – 1.10 – 18
- CHAPTER 2 19
- EXPLANATION OF OPERATION 19
- 2-1-1. Operations 20
- Heater block diagram (2/2) 22
- 2-1-2. Power supply 23
- 2-1-3. Main PCB 23
- Main PCB block diagram 24
- Main PCB Connector signals 25
- 2-1-4. 1394 PCB 27
- 2-1-5. I/F Connection PCB 27
- 2-1-6. IO PCB 28
- IO PCB Connector signals 28
- 2-1-7. IO2 PCB 29
- IO2 PCB Connector signals 29
- 2-1-8. Slider PCB 30
- Slider PCB Connector signals 30
- 2-1-9. Linear encoder PCB 31
- 2-1-10. The KeyBoard PCB 31
- 2-1-11. Take-up motor PCB 31
- 2-1-12. ID contact board 31
- 2-2. Ink system 32
- Refreshing operation 34
- Standby state 34
- Ink end monitoring 34
- Head cleaning operation 35
- Ink cartridge replacement 35
- Miscellaneous 35
- Ink parameters 1 36
- 2-2-4. IC Chip Function 37
- IC chip detecting timing 37
- CHAPTER 3 39
- TROUBLESHOOTING 39
- – 3.10 – 48
- 3-3-3. Cutting failure 49
- 3-3-4. Faulty cutter 50
- 3-3-5. Fan motor 51
- 3-3-7. Abnormal ink shot 52
- – 3.15 – 53
- 3-3-11. Cannot read the IC 54
- Main PCB 54
- 3-4. Plotting failure 55
- 3-4-2. Abnormal print 56
- – 3.19 – 57
- – 3.20 – 58
- – 3.21 – 59
- – 3.22 – 60
- – 3.23 – 61
- – 3.24 – 62
- 3-4-10. Banding occur 63
- 3-4-11. Vertical stripes 63
- 3-4-13. Ink drop or mist 64
- CHAPTER 4 65
- ADJUSTMENT 65
- 4-2. Maintenance item 68
- Pertinent Wiper height 75
- Pertinent Cap height 75
- (Insert from front side) 76
- Screw (M3) 76
- Wiper adjusting plate 0.5 76
- Cap adjusting plate 0.5 76
- Suction side connection joint 78
- Mounting screw 80
- Linear sensor PCB assy 80
- Optical axis 80
- – 4.17 – 81
- 4-2-12. Heater Replacement 83
- • Do not remove the cap bolt 84
- Write a number 85
- 4-2-13. Replacement Fuse 89
- – 4.26 – 90
- CHAPTER 5 91
- MAINTENANCE MODE 91
- 5-1. Maintenance items 92
- #PARAMETER 93
- key and 94
- Head2 Head1 99
- #PRN. adjust2 V2 101
- Y Bi. 1-1 : 0.0 101
- FINAL. 1-2 : 0.0 101
- FUNCTION 102
- Replace count 106
- 5-3-6. CAPPING 108
- 5-3-7. HEAD ID 109
- 5-3-8. SERIAL NO 110
- 5-3-9. DEALER NO 111
- 5-3-10. WORM WHEEL 112
- 5-3-13. SET QUALITY 117
- 5-3-14. MEDIA COMP2 118
- REMOTE/LOCAL 122
- 5-4-4. X SERVO 129
- 5-4-5. Y SERVO 130
- 5-4-6. XY SERVO 131
- 5-4-13. PUMP MOTOR 142
- 5-5. #PARAMATER items 153
- – 5.64 – 154
- – 5.69 – 159
- Error messages 159
- 5-7. Updating the firmware 160
- – 5.73 – 163
- – 5.74 – 164
- CHAPTER 6 165
- MAINTENANCE MENU TREE 165
- 6-1. Maintenance menu tree 166
- D500200-1.00-13122002 170
Related products and manuals for Print & Scan MIMAKI JV3-160S
Print & Scan MIMAKI UJF-706 Specifications
(184 pages)
(184 pages)
Print & Scan MIMAKI JV3-130SPII Specifications
(142 pages)
(142 pages)
Print & Scan MIMAKI JV5-130S Specifications
(292 pages)
(292 pages)
Print & Scan MIMAKI JV5-320S Specifications
(130 pages)
(130 pages)
Print & Scan MIMAKI Tx2-1600 Instruction Manual
(166 pages)
(166 pages)
Print & Scan MIMAKI UJF-6042 User Manual
(2 pages)
(2 pages)
Print & Scan MIMAKI TS5-1600AMF User Manual
(22 pages)
(22 pages)
Print & Scan MIMAKI JV33-160 Specifications
(202 pages)
(202 pages)
Print & Scan MIMAKI JV3-75SPII Specifications
(150 pages)
(150 pages)
© 2020, manymanuals.com. All rights reserved. | 0.851 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals