MIMAKI JV3-160S Setup Guide Page 52
- Page / 170
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
– 3.14 –
3-3-7. Abnormal ink shot
Problems Vertical lines during plotting, square spots, or plotting out of range.
Causes 1) The head FPC cable is in poor contact.
2) The connector of head has broken. (Metal corrosion)
3) The linear scale is not dirty or damaged.
4) The linear scale position is appropriate.
Checking procedure 1-2) Disconnect the FPC cable and then check the contact surface visually.
3-4) Visually confirm the Linear scale.
Remedies 1) Replace the head FPC cable with a new one.
2) Replace the head with a new one.
3) Replace the linear scale if very damaged.
4) Adjust the position of the Linear scale.
3-3-8. Ink-filling cannot be performed
Problems Ink-filling cannot be performed.
Abnormal ink cleaning.
Causes 1) There are some gaps for capping.
2) The pump motor has broken.
3) The IO PCB has broken.
4) The main PCB has broken.
5) The cap slider defect.
6) The pump defect.
Checking procedure 1) Visually confirm the ink-filling status.
2-4) Check whether or not the pump motor is running.
5-6) Visually confirm the cap and pump.
Remedies 1) Height adjustment for the station and position adjustment for capping.
2) Replace the pump motor with a new one.
3) Replace the IO PCB with a new one.
4) Replace the main PCB with a new one.
5) Replace the cap with a new one.
6) Replace the pump with a new one.
- JV3 Series 1
- FOREWORD 3
- TABLE OF CONTENTS 4
- CHAPTER 3 TROUBLESHOOTING 4
- CHAPTER 4 ADJUSTMENT 5
- CHAPTER 1 9
- OVERVIEW OF MAINTENANCE 9
- 1-1. Cautions in maintenance 10
- 1-4. Names of parts 12
- 1-4-2. Rear face 13
- Name Function 13
- 1-5. Specifications 14
- Item JV3-130S JV3-160S 15
- JV3 series specified ink 16
- 1Solvent ink (SPC-0334∗) 8 16
- – 1.10 – 18
- CHAPTER 2 19
- EXPLANATION OF OPERATION 19
- 2-1-1. Operations 20
- Heater block diagram (2/2) 22
- 2-1-2. Power supply 23
- 2-1-3. Main PCB 23
- Main PCB block diagram 24
- Main PCB Connector signals 25
- 2-1-4. 1394 PCB 27
- 2-1-5. I/F Connection PCB 27
- 2-1-6. IO PCB 28
- IO PCB Connector signals 28
- 2-1-7. IO2 PCB 29
- IO2 PCB Connector signals 29
- 2-1-8. Slider PCB 30
- Slider PCB Connector signals 30
- 2-1-9. Linear encoder PCB 31
- 2-1-10. The KeyBoard PCB 31
- 2-1-11. Take-up motor PCB 31
- 2-1-12. ID contact board 31
- 2-2. Ink system 32
- Refreshing operation 34
- Standby state 34
- Ink end monitoring 34
- Head cleaning operation 35
- Ink cartridge replacement 35
- Miscellaneous 35
- Ink parameters 1 36
- 2-2-4. IC Chip Function 37
- IC chip detecting timing 37
- CHAPTER 3 39
- TROUBLESHOOTING 39
- – 3.10 – 48
- 3-3-3. Cutting failure 49
- 3-3-4. Faulty cutter 50
- 3-3-5. Fan motor 51
- 3-3-7. Abnormal ink shot 52
- – 3.15 – 53
- 3-3-11. Cannot read the IC 54
- Main PCB 54
- 3-4. Plotting failure 55
- 3-4-2. Abnormal print 56
- – 3.19 – 57
- – 3.20 – 58
- – 3.21 – 59
- – 3.22 – 60
- – 3.23 – 61
- – 3.24 – 62
- 3-4-10. Banding occur 63
- 3-4-11. Vertical stripes 63
- 3-4-13. Ink drop or mist 64
- CHAPTER 4 65
- ADJUSTMENT 65
- 4-2. Maintenance item 68
- Pertinent Wiper height 75
- Pertinent Cap height 75
- (Insert from front side) 76
- Screw (M3) 76
- Wiper adjusting plate 0.5 76
- Cap adjusting plate 0.5 76
- Suction side connection joint 78
- Mounting screw 80
- Linear sensor PCB assy 80
- Optical axis 80
- – 4.17 – 81
- 4-2-12. Heater Replacement 83
- • Do not remove the cap bolt 84
- Write a number 85
- 4-2-13. Replacement Fuse 89
- – 4.26 – 90
- CHAPTER 5 91
- MAINTENANCE MODE 91
- 5-1. Maintenance items 92
- #PARAMETER 93
- key and 94
- Head2 Head1 99
- #PRN. adjust2 V2 101
- Y Bi. 1-1 : 0.0 101
- FINAL. 1-2 : 0.0 101
- FUNCTION 102
- Replace count 106
- 5-3-6. CAPPING 108
- 5-3-7. HEAD ID 109
- 5-3-8. SERIAL NO 110
- 5-3-9. DEALER NO 111
- 5-3-10. WORM WHEEL 112
- 5-3-13. SET QUALITY 117
- 5-3-14. MEDIA COMP2 118
- REMOTE/LOCAL 122
- 5-4-4. X SERVO 129
- 5-4-5. Y SERVO 130
- 5-4-6. XY SERVO 131
- 5-4-13. PUMP MOTOR 142
- 5-5. #PARAMATER items 153
- – 5.64 – 154
- – 5.69 – 159
- Error messages 159
- 5-7. Updating the firmware 160
- – 5.73 – 163
- – 5.74 – 164
- CHAPTER 6 165
- MAINTENANCE MENU TREE 165
- 6-1. Maintenance menu tree 166
- D500200-1.00-13122002 170
Related products and manuals for Print & Scan MIMAKI JV3-160S
Print & Scan MIMAKI UJF-706 Specifications
(184 pages)
(184 pages)
Print & Scan MIMAKI JV3-130SPII Specifications
(142 pages)
(142 pages)
Print & Scan MIMAKI JV5-130S Specifications
(292 pages)
(292 pages)
Print & Scan MIMAKI JV5-320S Specifications
(130 pages)
(130 pages)
Print & Scan MIMAKI Tx2-1600 Instruction Manual
(166 pages)
(166 pages)
Print & Scan MIMAKI UJF-6042 User Manual
(2 pages)
(2 pages)
Print & Scan MIMAKI TS5-1600AMF User Manual
(22 pages)
(22 pages)
Print & Scan MIMAKI JV33-160 Specifications
(202 pages)
(202 pages)
Print & Scan MIMAKI JV3-75SPII Specifications
(150 pages)
(150 pages)
© 2020, manymanuals.com. All rights reserved. | 0.373 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals